Manufacturing the future

Fine Grinding Mill (Centrifugal Roller Mill) Kurimoto Roller Mill [KURIMOTO, LTD.]

Contact US

Fine Grinding Mill (Centrifugal Roller Mill) Kurimoto Roller Mill

Division for this product Plant Engineering and Machinery Division

  • Contact us about this product
  • Print

Summary

The Kurimoto Roll Mill has a combined function of grinding, classifying, and pneumatic convey and a number of proven successful accomplishments for grinding phosphate rock, limestone, manganese dioxide, titanium oxide, coke, and others. Furthermore, by combining a pneumatic conveying dryer with the Kurimoto Roller Mill, you can perform grinding and drying at the same time as needed. This Roller Mill is broadly comprised of the following main unit and accessory equipment.

 

Main unit

Kurimoto Roller Mill

Used for fine grinding materials.

 

Accessory equipment

Rotary feeder

Used to feed materials.

Whizzer separator
(available for High-side model only)

Used to classify coarse particles.

Cyclone collector
(equipped with fine particles discharge damper)

Used to collect products.

Main fan

Used to transport products and circulate air.

Vent fan

Used to exhaust surplus air.

Bag filter

Used to support collection of products.

Ducts

Used to transport products and circulate air.

Hot air dryer (provided as needed)

Used to dry materials.

The Kurimoto Roller Mill has two models, Low-side Model and High-side Model (equipped with a whizzer separator on the top of the mill). The Low-side Model is best suited to grind materials up to -200mesh 80%, while the High-side Model for finer range than that. 

 

Features

  • The feed controller enables the Kurimoto Roller Mill to keep constant and smooth running and deliver a thorough grinding capacity. With this controller, an optimum amount of material can be automatically fed into the mill at all times.
  • Easy adjustments of product particle size
  • Grinding materials up to some 20m in particle diameter for 80% pass is enabled to a sufficient degree.
  • Negative-pressure air circulation system, which raises no dust in the room, providing clean and better working environment.
  • In combination with pneumatic convey, you can convey products to a randomly chosen point and classify them at the same time with a few workers.
  • You are able to grind and dry materials at the same time, and prevent the degradation of grinding capacity due to moisture to produce particles of a desired moisture level.
  • Large grinding capacity and compact design enable you to run this Kurimoto Roller Mill with a lower noise level compared to tumbling mills.
  • Minimized entry of iron during production makes this Kurimoto Roller Mill best suited to produce products, which are easily affected by iron.

 

Use

  • Phosphate rock
  • Limestone
  • Manganese dioxide
  • Titanium oxide
  • Coke

 

Construction

Specifications

SizeInside diameter of tireNumber of rollersGrinding capacity (t/h)Motor (kW)
-200mesh80%-350mesh95%
3035 770 3 1.2 0.7 19
3635 920 3 1.8 1.0 22
4247 1070 4 2.4 1.4 37<45
5057 1270 5 4.8 3.5 55<75
5457 1370 5 7.2 4.2 75<110
6058 1524 5 9.6 5.5 130<170
6669 1680 6 12.0 8.0 190<220
73612 1960 6 19.2 11.0 220<320
84616 2160 6 25.8 15.0 270<400

 

  • The above table shows the outline specifications of the main unit of the Roller Mill.
  • Grinding capacities are based on grinding tests with limestone of -15m/m up to that of -200mesh 80% and -350mesh 95%.
  • Rotating speed, horsepower, and others are subject to change according to kinds and conditions of materials to be ground.

Typical Flow Sheet

 

Division for this page Plant Engineering and Machinery Division

Back